osha raised platform railing requirements

those incidents and discusses current rules, standards, and best practices for protecting performers from fall hazards. cal-osha. as usual, cal-osha was the first regulator to cite a theater . putting railings on a set designed by. david hockney would . raised platforms, and other raised floor areas such as .

as already mentioned, there are federal osha standards which mandate guardrails or some other form of fall protection system be utilized to protect workers . four (4) feet above ground, on poles, and on towers, except when work platforms with suitable guardrails are provided on elevated work platforms.

osha fall protection requirements for general industry facilities is four feet. employers must use guard railing or a toe board for every floor hole that a worker may accidentally walk into and around every elevated open-sided platform, floor or runway. facilities that do not have work heights of .

osha standards for guarding openings and holes use the following denitions.platform. a working space for persons, elevated above the surrounding oor or ground. wall hole. an opening less than 30 inches but more than 1 inch high, of . across the opening prevents the use of a xed standard railing, the guard shall.

platform. a working space for persons, elevated above the surrounding floor or ground; such as a balcony or platform for the operation of machinery and . standard strength and construction. any construction of railings, covers, or other guards that meets the requirements of 1910.23. 1910.21(a)(8). stair railing.

railings on the market, not to mention the 2x4 or wire rope job-built railings you find on many construction sites . elevated workers. one such caveat specifically noted in the osha regulations for construction is if workers are working on stilts. for those readers not in the construction .

osha 1910.23(a) "protection for floor openings." (2) every ladderway floor opening or platform shall be guarded by a standard railing with standard toeboard on all exposed sides (except at entrance to opening), with the passage through the railing either provided with a swinging gate or so offset that a person cannot walk .

osha standards for walking/working surfaces apply to all permanent places of . system). protect from falling into ladderway floor hole or platform hole by guardrail system and toeboards on all exposed sides, except entrance . amends 1910.265 (sawmills) concerning elevated platforms and ladders.

when a walking platform is elevated above ground level (such as a catwalk), it is considered a runway. runways have the same requirements for guardrails with one exception: if work conditions or specialized use of the runway requires one side remain unguarded, no railing is needed provided the runway .

raised as to whether or not fall protection was needed for employees climbing on the face of a vertical rebar assembly such as one that would be constructed for a wall that was to be poured in place. in a letter of interpretation dated december 23, 1994, osha states that fall protection is not required .

guardrails shall be provided on all open sides of unenclosed elevated work locations, such as: roof openings, open and glazed sides of landings, balconies or porches, platforms, runways, ramps, or working levels more than 30 inches above the floor, ground, or other working areas of a building as defined in .

elevated platform requirements. step 1: examine the platform. · for all structures: ensure the passive fall protection (i.e.: guardrail) system on the working level of the platform meets or exceeds osha requirements; and all sides of the platform are protected. contact the competent person .

osha fall protection safety questions.

stairs that are higher than 12 feet tall require an intermediate landing in the middle of the stairway. these landings should be the same width as the stairway and extend at least three feet in length. for open-sided walking surfaces like stairs and elevated platforms, handrails and guards are mandatory.

standards 29 cfr§§ 1910.23 and .24(h) require employers in general industry to take specific precautions to protect employees who work from heights . cally, when working from any elevated platform. whenever . railing, the top rail will need to be raised or other fall protection means used while the step ladder is in place.

under 1910.23(e)(1), osha says that a guardrail must have a vertical height of 42 inches nominal from the upper surface of the top rail to floor, platform, runway, or ramp level. "nominal" simply means that 42 inches has been established as the de facto standard for guardrail height. osha allows for .